Thursday, April 7

Tutorial for MHS001

TUTORIAL ON HOW TO INSTALL SNAP BUTTON WITH THE TOOLS.


These are the button tools and 1 set of snap button (4 pieces).

TOOLS: -
Tool A - to make a hole on the fabric
Tool B - is for snap button set 1
Tool C - is for snap button set 2.
Beside the above tools, you will need a hammer and a piece of cloth too.

SNAP BUTTON SET: -
Set 1 - Above / Below
Set 2 - Above / Below

Please go through the tutorial before you get started.

Here we go....

Step 1 - Mark on the fabric where you want a hole on it (pls put a wooden board at the below to protect your table surface. Otherwise, your table will get a hole). Use Tool A and a hammer to make the hole.

Step 2 - Put the snap button set 1 (above) through the hole like the above photo.

Step 3 - Turn over the fabric to the other side and put the snap button set 1 (below) on top of snap button set 1 (above) like the above photo. Prepare Tool B and hammer.

Step 4 - Put the Tool B on top of snap button set 1 (below) and hold the Tool B straight up (90 degree) and hammer it. Remember to put a piece of cloth on the below when hammering in order to protect your button. You can hammer it until you get the below result (click the photo for bigger view for the inner)

This is what you get after a bit of hammering with Tool B.

Step 5 - Adjust and mark the other side of fabric (align with snap button set 1) and make a hole with Tool A and hammer. See the hole as below photo.

Step 6 - Get the snap button snap 2 (below) and insert it from the below fabric as per below photo. That's right. That is Nicky's chubby hand. LOL...

Step 7 - Get the snap button set 2 (above) and cover the snap button set 2 (below) like the photo. Ready Tool C and hammer.


Step 8 - Hold Tool C straight up (90 degree) and hammer it until you get the result. Make sure they fit tightly. If you see it still loose, hammer again. Remember to hold the Tool straight while hammering. Otherwise, you will ruin the button!


This is what I use during hammering to protect my button. Did you see a hole on it. Nicky hammered too strong with Tool A until went through it. Be careful with your table coz it might get a hole too. Better to use wooden board instead of steel below when you make the hole with Tool A. Otherwise, you will ruin your tool.

Tadaa... See, the result? Ok or not? ^^

This is the finished wallet. What do you think? I like the button the most. Hahaha

2 comments:

  1. This is a very useful tutorial. I have received the tools yesterday.. lyv it! Thanks Nicky.. :)

    ReplyDelete
  2. Thanks a lot dear. You are most welcome!

    ReplyDelete

Discount/Offer Corner

From now on, Nicky's customer will enjoy the special offer as per below: -

1) Every new customer who purchased RM 200.00 & above in a single receipt will enjoy a 10% discount from the total amount.
2) Every return customer will get a 10% discount from Nicky too! No min. order is required to enjoy this benefit as long as you are a return customer! You are my friend! So for those who have ever purchased with Nicky, pls let me know in your order to enjoy this discount ya!
3) Every return customer who purchased RM 180.00 & above in a single receipt will get another 5% of discount (meaning to say, after you get a discount of 10%, you will get another 5% of discount more)!

Terms: -
*Every discount calculated before add in the postage fee*
*All discounts given are calculated by Nicky based on *Normal Price* and all discounts are final*
*Clearance sales items are not applicable with this offer.
*Special price items are not applicable with this offer.
*Pls attach the discount code in your order via email when you are entitled to enjoy ya! Many thanks!

Discount Codes: -
New Customer: OFFER001
Return Customer: OFFER002
Return Customer+RM180: OFFER003